SAME70 with external RAM Hello,
without knowing the tool chain you are using it will be difficult to help you.
regards
Gerhard
Monday, 9 April 2018 - 11:57
Atmel at91sam9625 hello sandeep.
on Aria G25 module a AT91SAM9G25 is used and this part is still alive.
regards
gerhard
Monday, 18 September 2017 - 08:49
ATSAME70Q21 External Main Clock A tolerance of +/-50ppm will do it in any way with the peripherals you mentioned.
I won't clock a RTC with this tolerance, but for the rest it's fine.
btw:...
Friday, 4 August 2017 - 07:58
ATSAMC21 Samples? It seems that this chip isn't available before November at all.
Look at this link: http://www.microchipdirect.com/P...
If you really need samples and the y are...
SAME70 flash issue using the right forum will increase your chance for an answer:
https://community.atmel.com/forum...
regards
gerhard
Tuesday, 30 May 2017 - 10:51
AT91SAM7S512 and ATMEL-ICE programmer bojankoce wrote:
I have a custom PCB containing AT91SAM7S512 chip and JTAG connector. It seems that Atmel Studio 7 does not support this type of the processor (I can not see it...
Tuesday, 28 June 2016 - 12:19
SAM7 vs SAM4 debugging az10sbum wrote:
We are in the process of selecting a micro for a new project and are looking at SAM4 and SAM7 series parts. I have read some info that makes me think that...
Tuesday, 28 June 2016 - 12:14
MCU recommendation TonyZLR wrote:
Hello,
I'm looking for an MCU with the following capabilities:
1 - USB Device interface (Full speed OK, High speed would be a plus)
2 - An SDRAM controller to...
Monday, 27 June 2016 - 12:49
SAM E70 Xplain board - turning on IO Ports Acelink2 wrote:
Hi Guys, I've just received my SAME70 XPLAINED board and set it up. Installed Studio 7 board is detected and I can upload to the flash.
first of all, you posted at...
Monday, 27 June 2016 - 12:44
SAMA5Dx ASF / example projects hello albert,
regarding your questions:
Does this mean the SAMA5D36 on Xplained board cannot be programmed using JTAG/J-link as usual ?
usually j-link can only program...
Hello, without knowing the tool chain you are using it will be difficult to help you. regards Gerhard
hello sandeep. on Aria G25 module a AT91SAM9G25 is used and this part is still alive. regards gerhard
A tolerance of +/-50ppm will do it in any way with the peripherals you mentioned. I won't clock a RTC with this tolerance, but for the rest it's fine. btw:...
It seems that this chip isn't available before November at all. Look at this link: http://www.microchipdirect.com/P... If you really need samples and the y are...
did you enable data cache? if yes be sure that the txbuffer is located at a none-data cache area. regards gerhard
using the right forum will increase your chance for an answer: https://community.atmel.com/forum... regards gerhard
bojankoce wrote: I have a custom PCB containing AT91SAM7S512 chip and JTAG connector. It seems that Atmel Studio 7 does not support this type of the processor (I can not see it...
az10sbum wrote: We are in the process of selecting a micro for a new project and are looking at SAM4 and SAM7 series parts. I have read some info that makes me think that...
TonyZLR wrote: Hello, I'm looking for an MCU with the following capabilities: 1 - USB Device interface (Full speed OK, High speed would be a plus) 2 - An SDRAM controller to...
Acelink2 wrote: Hi Guys, I've just received my SAME70 XPLAINED board and set it up. Installed Studio 7 board is detected and I can upload to the flash. first of all, you posted at...
hello albert, regarding your questions: Does this mean the SAMA5D36 on Xplained board cannot be programmed using JTAG/J-link as usual ? usually j-link can only program...
hello, did you observe all the hints regarding power-up/down of the schematic check list? regards gerhard
Pages