HV (Arduino) Programmer Unable to Set Fuses - ATtiny85 bWildered1 wrote:
jkwilborn wrote:
Sounds good, all of it at one place. I think the manual is as close as it comes. I think that's an impossibility with these devices...
HV (Arduino) Programmer Unable to Set Fuses - ATtiny85 jkwilborn wrote:
Many op codes have variable number of parameters. For instance an 'immediate load', might only be two bytes in object code (machine code,) first is the op...
HV (Arduino) Programmer Unable to Set Fuses - ATtiny85
westfw wrote:
In theory, 12V on RESET works to put the device into "HV Serial Programming Mode" even if the fuse has reset disabled.
OK.
It should therefore be possible to use...
Saturday, 8 June 2019 - 11:00
HV (Arduino) Programmer Unable to Set Fuses - ATtiny85 Hi clawson
Keeping well, I trust.
Reverse voltage, no.
ESD is always a possibility, no matter how careful a person might be.
My short term memory is not what is once...
Friday, 7 June 2019 - 17:34
MPLAB Forum Moe123 wrote:
From my experience this will happen in the next few years....say 2025 ?
Mars?
Microchip would tell us we are already there.
Wednesday, 17 April 2019 - 17:06
MPLAB Forum Thanks.
I think I had already done that, but I did it again anyway just in case.
gchapman wrote:
edit : 'Device Support.htm' in the release notes zip; MPLAB X...
Sunday, 14 April 2019 - 13:12
MPLAB Forum Hi all
Does anyone know if there is a way to be informed when Microchip sorts out the AVR related problems with MPLAB X?
An email list, for example.
Take care...
Sunday, 14 April 2019 - 09:25
MPLAB Snap clawson wrote:If you want to learn AVR I'd get a JTAG model where debugging is the easiest of all. Wouldn't mess about with resource limited Tiny's or some even more limited...
bWildered1 wrote: jkwilborn wrote: Sounds good, all of it at one place. I think the manual is as close as it comes. I think that's an impossibility with these devices...
jkwilborn wrote: Sounds good, all of it at one place. I think the manual is as close as it comes. I think that's an impossibility with these devices. You can...
jkwilborn wrote: Many op codes have variable number of parameters. For instance an 'immediate load', might only be two bytes in object code (machine code,) first is the op...
Jack, thou art gifted. As I write this, one of the new ATtiny85 devices is winking away at me with a certain nonchalance. But first, I'll dispose with the side...
jkwilborn wrote: The tiny85 is an 8 pin package... Pin 13? Arduino UNO (ATmega328P based) pin 13. Take care Mike
Brian Fairchild wrote: So the 12V is on the reset pin UNLESS pin 13 is high? Yes... An extract from the Arduino HV Programmer sketch... void setup() {...
westfw wrote: In theory, 12V on RESET works to put the device into "HV Serial Programming Mode" even if the fuse has reset disabled. OK. It should therefore be possible to use...
Hi clawson Keeping well, I trust. Reverse voltage, no. ESD is always a possibility, no matter how careful a person might be. My short term memory is not what is once...
Moe123 wrote: From my experience this will happen in the next few years....say 2025 ? Mars? Microchip would tell us we are already there.
Thanks. I think I had already done that, but I did it again anyway just in case. gchapman wrote: edit : 'Device Support.htm' in the release notes zip; MPLAB X...
Hi all Does anyone know if there is a way to be informed when Microchip sorts out the AVR related problems with MPLAB X? An email list, for example. Take care...
clawson wrote:If you want to learn AVR I'd get a JTAG model where debugging is the easiest of all. Wouldn't mess about with resource limited Tiny's or some even more limited...
Pages