Post Created date
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Yes, I did have two versions there, one from earlier this a.m. and the other from this afternoon.  Deleted the earlier one, AS7 seems to be fine with that.   Thank you....
Monday, 18 March 2019 - 20:34
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Part of my installation issues have been found to be related to our corporate Carbon Black (Cb) antivirus.  Microsoft event log shows Cb is blocking some exe activity during...
Monday, 18 March 2019 - 18:19
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Ok gchapman, thanks for the pointer to version 7.0.1417.  Now downloading...
Monday, 18 March 2019 - 15:30
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Thank you clawson, "set" did allow me to locate those locations. 
Monday, 18 March 2019 - 14:15
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
I did try to run as Admin and also make sure the directories in question were R/W permissions - no help.  I've now reverted my PC, again, to a state prior to the upgrade. I...
Monday, 18 March 2019 - 13:38
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Not working for me at all.  Very disappointing that Ive used this tool for a couple years with no issues, now I cannot install and reinstall the same version successfully....
Monday, 18 March 2019 - 12:45
Atmel Studio 7 Upgrade Issues Ver.7.0.1417 to Ver.7.0.1931 on WIN10
Thank you.  Now, how do I completely uninstall the version 7.0.1931.  The uninstall doesn't seem to do anything but try to install. 
Friday, 15 March 2019 - 17:45
SPI Issue reading External ADC - AD7175-8 ID Register, using SAM4SA16B
I have found that it was necessary to perform a :     spi_get(SPI); // remove existing SPI data before sending a command/reading register to the external analog to...
Monday, 23 October 2017 - 12:29
SAM4s SPI Mode 3 - Use ASF or Bit-bang the interface?
I have found that it was necessary to perform a :     spi_get(SPI); // remove existing SPI data before sending a command/reading register to the external analog to...
Monday, 23 October 2017 - 12:27
SAM4s SPI Mode 3 - Use ASF or Bit-bang the interface?
FWIW I basically daisy chained 3 devices on the SPI bus.  Tried to minimize stubs.  The ADC is the last device on the bus.  I think if there were a signal integrity...
Thursday, 12 October 2017 - 21:09
SAM4s SPI Mode 3 - Use ASF or Bit-bang the interface?
I have probed the SPI CLK (which is 3.1" of 6mil trace over a ground plane) at the ADC device, with a very short ground lead.  The clock signal looks good, aside from some...
Thursday, 12 October 2017 - 14:14
SAM4s SPI Mode 3 - Use ASF or Bit-bang the interface?
Tarribred, Thank you, so much, for your reply.  I will switch from logic analyzer to the scope and inspect the integrity of the signals at the ADC ( far end of the SPI traces...
Thursday, 12 October 2017 - 12:59

Pages