| Discussion Title | Created date |
|---|---|
|
Serial ADC---Interface with AT90USB1287 in USART SPI mode Hey...everyone I am interfacing serial ADC. I need some help , regarding USART in SPI mode, http://www.mouser.com/ds/2/256/M... ... 102916.pdf It requires 24 continuous clock... |
Wed. Nov 6, 2013 - 03:56 AM |
|
AT90USBKEY2 External ADC reference voltage Dear all, I want to use ADC of At90usb1287. In the datasheet it is mentioned that reference voltage can be 0-Vcc. I want to give 1.023V reference voltage to Aref pin. I... |
Thu. Oct 31, 2013 - 05:43 AM |
|
pulse counter using usb1287 Hello to all, I am trying to make pulse counter using usb1287 controller. The pulse output available has specifications: Max. Pulse rate : 3.3*10E5, Pulse width =... |
Thu. Aug 22, 2013 - 06:25 AM |
|
SPI clock always running...how to do that? I have at90usb1287 and I want to use spi hardware to connect to external ADC which supports SPI. Here, I am able to see data and clock signal out only when controller sends the... |
Tue. Jul 2, 2013 - 05:02 PM |
|
Atmega128 ADC - Sampling Frequency. I have atmega128A connected to external 16MHz crystal. I am trying to check maximum ADC samples it can support. After reading datasheet and other posts on forum I want to post my... |
Wed. May 30, 2012 - 09:19 AM |
|
strange problem,,,,,,ISP. Hello to all...... I have one sensor which gives data through RS-485...I used atmega32 and max485 to read the sensor data...I have used isp programming to program atmega32...(... |
Fri. Sep 9, 2011 - 02:09 PM |
|
At90usb1287 & Bluetooth Usb dongle Hello all.... I am looking for bluetooth connectivity between uC and mobile phone....I found bluetooth module little expensive, but this usb dongle is cheaper....Is this possible... |
Sun. Jul 24, 2011 - 09:37 AM |
|
Atxmega series controller programming... Hello to all... I am looking for programming xmega series controller....I found that it does't support SPI programming which I used to program atmega series... |
Tue. Jul 5, 2011 - 07:25 AM |
|
SD card, USB Pendrive & Avr controller I want to design a system in which one avr controller collects data and stores it in SD card(2 GB)... and I want to have one usb port. So whenever user add its USB STICK in the... |
Thu. Jun 30, 2011 - 05:24 AM |
|
timer1 as counter In at90usb1287, I want to use timer1 as counter... I have connected my pulse source to pin no.31 (T1)PD.6. I want to use prescale=1 I have defined registers as TCCR1A=0 TCCR1B=129... |
Wed. Nov 24, 2010 - 05:55 AM |
|
at90usbkey and at45DB642D help!!!!! I want to save data to data-flash at45db642 present on at90usbkey... After reading the datasheet of dataflash I am trying to write 3 bytes in buffer1 and trying to read the same... |
Mon. Nov 15, 2010 - 10:01 AM |
|
at90usbkey I want to give Aref a 5V in At90uskey...How to make Vcc 5V? I want to use external power supply and use usb1287 as a device mode... making Usbcon pin high will do that??? |
Mon. Oct 4, 2010 - 09:14 AM |