Post Created date
Raven Restore Firmware -- Resolved
Don't know about 3290, but 1284 ISP connector should be standard. Like regular 10-pin connector but shrinked down in size. Although I even don't bother to understand Raven's...
Monday, 10 August 2009 - 16:12
Raven Restore Firmware -- Resolved
I don't think you can restore original firmware just by setting some jumper. And for the connector I personally would recommend soldering good old PLD connector on wires. This...
Sunday, 9 August 2009 - 18:38
[Meshbean ZigBee BitCloud RSSI] Obtain RSSI value
RSSI will be available on the receiving side. So if you want to determine strength of router's signal at coordinator antenna (RSSI) then you must transmit from router. PS: RSSI is...
Wednesday, 5 August 2009 - 12:06
[Meshbean ZigBee BitCloud RSSI] Obtain RSSI value
ZDO_GetLqiRssi() returns RSSI value saved from last received frame from any given node. To get actual values you will need to transmit data as often as you wish to get RSSI value.
Wednesday, 5 August 2009 - 09:48
[Meshbean ZigBee BitCloud RSSI] Obtain RSSI value
RSSI is updated on every frame transmission (reception actually). For RangeTest application transmission is performed continuously and RSSI value updated accordingly.
Wednesday, 5 August 2009 - 07:28
[ZigBee Bitcloud] Problem with peer2peer application
629PKJ75 wrote:I'm totally lost with peer2peer application, from Meshnetics. I don't know how to make working this application (boards configuration, serial port...) is anybody...
Saturday, 1 August 2009 - 07:59
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote:so I can't insert my ADC IRQ function.... HAL and BSP are open-source - insert anything you like. Just be careful.
Wednesday, 22 July 2009 - 12:43
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote: Ok, but its write for WinAVR compiler, I like to use CodeVision AVR :) and BitCloud links to precompiled libraries that compiler always using when I need, for...
Wednesday, 22 July 2009 - 12:41
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote:So in what registers I can write 64bits CS_EXT_PANID? PAN_ID only is 16 bits. In no register. Seriously, read standard (ZigBee + MAC) and try to understand that...
Wednesday, 22 July 2009 - 10:06
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote:In each meshnetic board there an MAC-address (8 bytes/ 64 bites). It's defined in UID chip. Zigbit OEM modules haven't it. Do I need to set this MAC-address? And...
Tuesday, 21 July 2009 - 10:54
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote:extPANid is IEEE_Addr (regs. 0x24 - 0x2B)? extPanId is not in registers. RF-Chip contains only values that are needed for automatic frames filtering/ack-ing. code-...
Tuesday, 21 July 2009 - 07:09
Can't compile samples from BitCloud (ZigBee) with WinAVR
code-by wrote:I make my self program that reading registers PART_NUM, VERSION_NUM, MAN_ID :) Good start! code-by wrote: If I want for example create 10 different zigbee networks...
Monday, 20 July 2009 - 17:01

Pages