Type in the full discussion title or a part of it.
Discussion Title Created date
What does "rjump ." mean?
I see the assembly instruction "rjmp ." with a dot '.' after the 'rjmp'. Does this mean it simply like a no-op jump but takes two cycles?
Friday, 4 May 2012 - 03:53
How would I connect a crystal to the ATTINY13?
Hi, The ATTINY13 does not have an XTAL1/XTAL2 pin but just a CLKI. Can I simply attach two 22pF to each of the crystal's terminals and connect in series one of the crystal's...
Saturday, 21 April 2012 - 13:19
Lots of questions on the CS4334 stereo DAC
Hi all, I am looking to do a sound/music project, basically streaming PCM data to the CS4334 stereo 2-channel DAC. The CS4334 datasheet is at http://www.cirrus.com/en/pubs/pr......
Friday, 13 April 2012 - 05:35
How can I disassemble a hex file?
This is for the ATMEGA8 hex file. Is there is a really good disassembler? Thanks
Thursday, 22 March 2012 - 00:20
Can JTAGICE MkII programmer use to program the ATTINY10?
Hi, I've looked over the net. And all I can find is that AVRISP MkII programmer can be used to program the ATTINY10. What about the JTAGICE MkII, which I have?
Saturday, 25 February 2012 - 10:50
How can I get my AT32UCL064 I/O pin to source 3.0V?
Hi, I am able to make a LED program run on my AT32UCL064 device. I measure the voltage coming out of the I/O pin, and it's about 1.5V (almost to 1.6V), which is what the spec...
Sunday, 12 February 2012 - 02:25
Can't read fuses of my AT32UCL064 device from AVR32 Studio
I am using JTAGICE MkII with AVR32 Studio. Every time I try to read the fuses for the AT32UCL064, AVR32 Studio says the below: Could not read fuses Cannot run program "...
Friday, 10 February 2012 - 05:46
ASF question...
hi, I downloaded ASF and installed. I also have AVR32 Studio installed. All of these on Vista. Note that I don't have AVR Studio 5 installed. I go into one of the avr32 ASF...
Thursday, 9 February 2012 - 06:36
Bootloader for the AT32UC3L064 device?
Hi, I bought some AT32UC3L064 from digikey.com. I am trying to confirm if the AT32UC3L064 comes, that is, pre-programmed with a bootloader by the manufacturer, Atmel. I thought...
Tuesday, 7 February 2012 - 16:46
Can't update firmware to my JTAGICE MkII STK600 programmer
hi, I am new to AVR32. I am using AVR32 Studio not AVR Studio 5.0, because WINDOWS Vista a pain on my computer. WINDOWS Vista fails ITSELF to do SP1/SP2 update, which is...
Sunday, 5 February 2012 - 04:36
basic question on the fuse bit for external crystal
hi, I've always used 16Mhz external crystal for my ATMEGA8. Now I have a project that I want to try out using only 4Mhz, again, as external crystal. Looks there are three choices...
Sunday, 22 January 2012 - 23:49
Op-amp replacement/substitute for NE592N8G?
Hi, I found a project on the net that uses the NE592N8G (datasheet at http://search.digikey.com/us/en/... ) op-amp. DigiKey does not sell by the piece. Posting this message to...
Saturday, 21 January 2012 - 16:51