AVR Freaks

How to change the ISP speed? Do you have any guidance for that because I'm a little bit lost

so this is my arguments : -c usbtiny -p m328p -v -v -v -U flash:w:$(TargetDir)$(TargetName).hex:i  -U lfuse:w:0xFF:m -U hfuse:w:0xDE:m -U efuse:w:0x05:m

where do I need to but the -B 125 kHz? because I already put something like this: -c usbtiny -p m328p -B 125kHz -v -v -v -U flash:w:$(TargetDir)$(TargetName).hex:i  -U lfuse:w:0xFF:m -U hfuse:w:0xDE:m -U efuse:w:0x05:m

and it shows that avrdude.exe: invalid bit clock period specified '125kHz'

is it in command line or in arguments?

Edited

Hi now I did some changes:

1. change into atmel studio 6

2. change my programmer with an usbasp as the one you suggested except my model don't have the 3 pin male header (my version is MX-USBISP-V3.01)

3. buy a new breadboard and bunch of jumper wires

and I have so called a new problem as the command prompt result show this:

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e940b
avrdude: Expected signature for ATMEGA328P is 1E 95 0F
         Double check chip, or use -F to override this check.

avrdude done.  Thank you.

it seems I can't upload any program to it as the output window of atmel studio show this (see below picture) :

avrdude.exe: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude.exe: Device signature = 0x1e940b
avrdude.exe: Expected signature for ATMEGA328P is 1E 95 0F
             Double check chip, or use -F to override this check.

avrdude.exe done.  Thank you.

do you guys know how to rectify this issue?

My current programmer is : MX-USBISP-V3.01

Hi yeah just now I realized my mistake that I thought I programmed the ATmega328p and it turned out that I did the connection for ATmega168p

but once I change the command become: C:\Users\rizki>avrdude -c usbasp -p m168p

the response was: avrdude: AVR Part "m168p" not found.

how to fix the above new error code now? since based on the list of device it is only available for the ATmega 168, not ATmega168p

and I realized that I think my ATmega 328p had a problem since now I repeat the same connection as what I did to ATmega 168p and the response still the same:

so I believe that my ATmega 328p was spoiled or damaged right since I already tried the following command as others suggested me in this thread

But then I still get an error code that rc = -1 if I use ATMega 328p and if I use ATmega 168P it shows that the model is not available on the usbasp device list
Please help me about this cause I feel exhausted and a little bit sad

Yes this one was the same thread as last time I used the AS7 but I'm not sure which avrdude I used last time
So now I need to go back to the AS7 with AVRDUDE 6.3?

1. the following picture is when I want to play with the B or the speed of the ISP

2. the following picture when I just enter a regular command 

3. the following picture is the more detail whereby I put four v alphabets

thanks man for helping me, these are my connection pictures

note that for the wire colour

Red is for Vcc

White and Black for GND

the capacitor that used has 104 written on it which is 0.1 uF or 100nF

orange cable is for MOSI

Blue cable is for MISO

yellow cable is for SCK

grey cable on pin number 1 is a reset

1. First picture is ATmega328p connection

2. The following picture is the view from the pin number 1 of the 2x5 female header

3. This the other side view of 2x5 female header is the Vcc and GND located

but in my previous picture that I uploaded there was a statement 

it showed that "cannot set sck period, please check for the update usbasp firmware update"

is it a problem or just something that I can ignore?

So what are my problems in this case? Can you help me to check out? Just now I remember that this ATmega I took it from my friend's arduino. Is that an issue also?

Yes I checked with my voltmeter between each Vcc and GND I got approximately 5 V. So now what changes should I make? I double check my pins from the usbasp that the 5V also appear between the Vcc and GND

Ok I'll check that out but I need to make this one work as I really need to study an 8 bit microcontroller as a basic

I do have another adapter from the 10 pin to 6 pin or 10 pin but it comes from the sparkfun

so from that arduino I do the same thing what I've done with the AVRDUDE and AS7? but my friend brought his old arduino board so I can't test it ASAP. I want to try with the ATMega 168p as I have a progress now but below is my new problem because I was too excited and jumped to the AS7 directly

Hi bro sorry just  a quick update, just now I was playing with the ATmega 168p again (comes from the element14 fresh out of the box)

when I enter in the command prompt, I got the result as following: 

but my mistake because too happy was directly tried in the ATMEL STUDIO 7 and try to upload with the external tools and I got the result as following (I apologize if I put too many pictures but now I think I spoiled my ATMega 168P because I burned the fuse right?)

and then it repeat the same thing until skipping page 127 at the last one

and once I checked in the command prompt it become like this again (so sad now)

Yes now I think I want to go for the other option which is through the uno clone board. 

I do have the cheap uno clone board, but it comes with the ATMega 328p SMD package. I don't want to use the arduino programming language, I want to handle with the C programming when I control the ATMega 328p on the uno clone board, is that possible? How to do that? 

if I want to use for the project that uses SPI, I2C,  and UART, is the arduino uno clone is sufficient enough for my desire?

Ok I'm going to start to program the atmega 328p with the help of Arduino board and now I able to turned off or on an LED with AS7, but I got an additional question because the Arduino atmega 328p has a clock speed of 16MHz as the following picture show and I want to follow the programming/project tutorial from the book "Make: AVR Programming" by Elliot Williams , will it cause a problem because I assume that my Arduino atmega 328p works too fast.  And I saw that in the sample code that the book gave they mention about this statement: #define F_CPU = 1000000UL

Please enlighten me about this issue. 

Yes, now my hello word is succeeded already and I was very happy with this. But I have an additional problem because the 

because the Arduino atmega 328p has a clock speed of 16MHz as the following picture show and I want to follow the programming/project tutorial from the book "Make: AVR Programming" by Elliot Williams , will it cause a problem because I assume that my Arduino atmega 328p works too fast. Please enlighten me about this issue. And I saw that in the sample code that the book gave they mentioned  about this statement:

#define F_CPU = 1000000UL

Please enlighten me about this issue. 

Sure thanks man but I have an additional issue that I mentioned above section of my reply, please help me to answer that 

Hmm I think I'll get back to you in the future when I apply and use the ADC because now I'm still at the starting of the basic part

Sure noted now I learnt a new stuff thanks for you guys and this community I love it because everyone is helping each other

so everytime inside my program I must put the statement that you explained right? now I understand and will start tomorrow when I'm in the school lab ( I don't have so much resources, so I'm dependent on them) 

thank you for your help and will get to you back later if I have the problem with the clock speed

Anyways a little bit out of topic but if I don't ask I keep thinking because I keep imagining , so my question are:

1. what is the meaning of 1MHz statement in the microcontroller? because 1MHz as far as I know it as frequency but I don't know which frequency, is it a microcontroller frequency? I want to find out but I couldn't find the answer in the datasheet

2.  what is the meaning of this statement? where do I could find the information of this function?

 clock_prescale_set(clock_div_16);  //run your 16MHz hardware at 1MHz

3. and then we frequently uses _delay_ms function. if for example "_delay_ms(1000);" does it mean that the delay always one second regarding any frequency the microcontroller works? 

I hope you could clarify my questions and give me good sources to read if you don't mind

I know I've been asking a lot of questions but really it always bother me because I don't know the meaning of it