I can not Programmer (ATZB-256RFR2, ATZB-X-233-USB STICK, ATZB-X-233) Zigbit

Log in or register to post comments
Go To Last Post
4 posts / 0 new
Author
Message
marthur
marthur's picture
Level: New Member
Joined: Mon. Nov 11, 2013
Posts: 1 View posts
#1
Posted by marthur: Thu. Sep 17, 2015 - 08:39 PM
  • 1
  • 2
  • 3
  • 4
  • 5
Total votes: 0

I have three different extensión boards how:

 

 

 

ATZB-256RFR2-XPRO EXPLAINED EXT ZIGBIT.

 

ATZB-X-233 -XPRO EVAL BOARD XMEGAA3U RF233 FOR 2.4 GHZ ZITBIT.

 

 

ATZB-X-233-USB STICK ZIGBIT.

 

When I wanted to program these, I see the user guide “http://www.atmel.com/Images/Atmel-42186-ZigBit%20Extension-User-Guide.pdf “. On the section 1.5.1 JTAGICE. It says to me “How to program using the AVR® JTAGICE mkII and JTAGICE3.”  Then I went to Atmel page to buy the programmer.

The first option was  JTAGICE mkII but I wanted to buy It. In the page there was a message, It say that programmer is discontinued and the replacement was Atmel-ICE

The second option was JTAGICE3 But Atmel don’t had available units. Then I bought  The Atmel-ICE.

 

My problem is:

  1. I cannot program nothing of extension board above mentioned.
  2. When I open The AtmelStudio 6.2.9 in Tools==>DeviceProgramming.           

the following error appears.

 

 

I like to know if somebody can help me to program these extension boart with a good advice.

Marthur

Tahnk you

 

 

 

 

Tags:

Wireless, 802.15.4/ZigBee
Last Edited: Thu. Oct 15, 2015 - 09:54 PM
Top
alexru
alexru's picture
Level: Raving Lunatic
Joined: Wed. Apr 15, 2009
Posts: 8059 View posts
Location: San Jose, CA
Posted by alexru: Thu. Sep 17, 2015 - 10:08 PM
  • 1
  • 2
  • 3
  • 4
  • 5
Total votes: 1

First check that you can read Device Signature and Target Voltage. This will verify debugger connection.

NOTE: I no longer actively read this forum. Please ask your question on www.eevblog.com/forum if you want my answer.

Top
alexru
alexru's picture
Level: Raving Lunatic
Joined: Wed. Apr 15, 2009
Posts: 8059 View posts
Location: San Jose, CA
Posted by alexru: Thu. Sep 17, 2015 - 10:09 PM
  • 1
  • 2
  • 3
  • 4
  • 5
Total votes: 1

Also, the error says that target power is not detected. Do you actually have power on that board?

NOTE: I no longer actively read this forum. Please ask your question on www.eevblog.com/forum if you want my answer.

Top
Sashal
Sashal's picture
Level: Hangaround
Joined: Mon. Jan 27, 2014
Posts: 135 View posts
Location: Kharkov, UA
Posted by Sashal: Fri. Sep 18, 2015 - 06:57 AM
  • 1
  • 2
  • 3
  • 4
  • 5
Total votes: 0

Also try connect RESET to GND. If your MCU sleeps, it must help.

Top