ZeptoProg II AVRISP mkII compatible AVR Programmer and Multitool

Updated: Apr 16, 2012

Description

The ZeptoProg II™ is an AVRISP mkII compatible USB AVR programmer that supports chips with the ISP, PDI, or TPI programming interfaces, which includes most megaAVR®, tinyAVR®, and XMEGA™ series devices. It supports high-speed in-system programming of the AVR flash, EEPROM, fuses, lock bits, and more using AVR Studio 4.19, 5.x, or AVRDUDE. Target boards operating at 2V to 5.5V are supported. A jumper can be installed to provide 5V through a polyfuse to the target board. Additionally, a mutitool mode implements a simple 4-channel logic analyzer, GPIO, PWM, frequency output, frequency measurement, a SPI interface, and configuration, all accessible using the ZeptoProg II Java application or the command line using a terminal emulator. Finally, the USB to serial bridge can be used to connect the target to a computer over USB (virtual COM port) at up to 2Mbps.

Features:
● AVRISPmkII compatible AVR Programmer
■ Supports all AVRs with ISP, PDI, or TPI programming interface using standard pinouts
○ Includes megaAVR, tinyAVR, XMEGA, and USB, PWM, and CAN AVRs
■ Optional 5V output via headers to target board, with standard jumper and polyfuse
■ Up to 8MHz programming speed with optional recovery clock
■ Program flash, EEPROM, fuses, lock bits, and more
■ Works with AVR Studio 4 and 5.x, AVRDUDE, Codevision, and BASCOM 2.0.6
● Multitool
■ Interface using Java GUI application or command line (via terminal emulator)
■ Logic Analyzer (GUI only)
○ 4 channels, trigger on any combination of pins (or immediately)
○ Fast mode: 1024 samples at 2Msps
○ Auto mode: samples on external clock, up to 60Ksps, up to 10K samples
○ Manual mode: configurable sample rate up to 100Ksps, up to 10K samples
○ Pre-trigger buffer (up to 10K samples) and post-trigger delay (up to 50K samples)
■ GPIO / PWM / frequency input & output
○ 7 TTL inputs, 9 outputs (5 level shifted)
○ 2 PWM outputs with separate duty cycles
○ 1 frequency output
○ 1 frequency measurement input
■ SPI Interface
○ Up to 8MHz clock, ZeptoProg II is master, Modes 03, MSB or LSB
○ 4 chip select outputs (pushpull or opendrain w/ optional pullup)
● Serial Bridge
■ Separate serial pins (simultaneous connection of programming cable and serial RX/TX)
■ Up to 2MHz baud rate, synchronous or asynchronous operation
■ Optional flow control via _CTS_ and _RTS_ pins, 9bit support
● Upgradeable firmware / USB bus powered
● 2 buttons for control / 2 LEDs for status indication
● Target board voltage support of 2V to 5.5V via levelshifted pins on two main headers
● Reverse polarity protection on Vtgt and GND pins
● Overcurrent protection on all output pins via series resistors (signal) and polyfuse (power)
● Measures 5.9cm x 1.8cm x 1.2cm, 1.57mm (0.063”) PCB thickness
● Compatible with Windows XP/Vista/7 and Linux, with Mac support in progress.
● Uses the AVRISP mkII clone and LUFA library by Dean Camera (http://www.lufa-lib.org).

Includes one 30cm (~1ft) 6-pin programming
cable and four 30cm 1-pin cables.

Categories

• Other

Version	Presented by	Website	Price	Rating
120308	(Find Distributor)	http://www.mattairtech.com/...	$24.99